Code:
dmesg | grep tone
[196302.113796] dahdi: Registered tone zone 0 (United States / North America)
[196302.222100] dahdi: Registered tone zone 2 (France)
[521929.557626] dahdi: Registered tone zone 0 (United States / North America)
[521929.639958] dahdi: Registered tone zone 2 (France)
[522616.260987] dahdi: Registered tone zone 0 (United States / North America)
[522616.352689] dahdi: Registered tone zone 2 (France)
[525599.874406] dahdi: curzone: ffff88006ee04000, tonezone: 2, curtone: (null), tonep: 0
J'ai bien inclus le dans chandahdi le dahdi.conf comme tu me l'avais dit.
Code:
cat /etc/dahdi/genconf_parameters
#
# /etc/dahdi/genconf_parameters
#
# This file contains parameters that affect the
# dahdi_genconf configuration generator.
#
# Syntax:
# * A comment from '#' to end of line
# * Blank lines ignored
# * Whitespace at end of line trimmed
# * Single valued items:
# key <whitespace...> value
# * List valued items:
# key
# <whitespace...>value1
# <whitespace...>value2
# ...
#
# When generating extensions for chan_dahdi.conf or users.conf etc: the
# extension number will be channel_number+base_exten . The default is:
#base_exten 4000
#
# Make FXS (analog phones) extensions answer immediately (sets
# 'immediate = yes' for them in chan_dahdi.conf). Don't enable this before
# you're read documentation about this option.
#fxs_immediate yes
#
# For FXS (analog phones) - use KS or LS? ks is the only method for
# Asterisk to provide disconnect supervision and thus it would normally
# be preferred and is the default.
#fxs_default_start ls
#
# For FXO (analog lines) - use KS or LS? KS is the default and is
# normally the better choice as it allows detecting hang-ups on many
# lines.
#fxo_default_start ls
# Set tone zone values. This is used for playing tones (busy, dial-tone
# and such). The default is 'us'. This sets the value for both loadzone
# and defaultzone in system.conf .
lc_country fr
# The dialplan context into which to send trunks in chan_dahdi.conf or
# users.conf. The default value is:
context_lines from-pstn
#
# The dialplan context into which to send extensions in chan_dahdi.conf or
# users.conf. The default value is:
context_phones from-internal
#
# Two extra contexts for the input ports and output ports of an
# Astribank. Default values are:
#context_input astbank-input
#context_output astbank-output
# A group to put all analog phones in. By default 0, so you can dial to
# the 'first phone available' using Dahdi/g5 .
#group_phones 5
#
# A group in which to put all the channels belonging to some trunk.
# Thus you can dial through "some trunk" using Dahdi/G0/NUMBER
#group_lines 0
# Channels of digital trunk of span N are also added to group 10+N (that
# is: 14 for channels of span 4).
# Do we want to use PtP ('bri') or PtMP ('bri_ptmp') for BRI? PtMP
# allows connecting several CPE devices on the same network device
# (several BRI phones on the same line, kind of like several analog
# phones on the same analog line). However it is generally brings
# unnecessary complexity for a pbx-pbx connection. It is still the
# default as this is normally what you get for a BRI PSTN connection.
#bri_sig_style bri
#
# If this option is set (that is: not remmed-out), BRI NT ports will
# also be set as overlap. This is useful if you want to connect ISDN
# phones.
#brint_overlap
# The echo canceler to use. If you have a hardware echo canceler, just
# leave it be, as this one won't be used anyway.
#
# The default is mg2, but it may change in the future. E.g: a packager
# that bundles a better echo canceler may set it as the default, or
# dahdi_genconf will scan for the "best" echo canceler.
#
#echo_can hpec
echo_can oslec
#echo_can none # to avoid echo canceler altogether
# bri_hardhdlc:
# 'yes' - forces BRI cards to use 'hardhdlc' signalling.
# 'no' - forces BRI cards to use 'dchan' (an alias for 'fcshdlc').
# It is usefull only for dahdi with the bristuff patch.
#
# If it is left out or set to 'auto':
# * Information supplied by the driver is used to decide:
# - Currently implemented for Astribanks.
# - Taken from /sys/bus/xpds/drivers/bri/dchan_hardhdlc.
# * Without this info, falls back to 'hardhdlc'.
#bri_hardhdlc auto
# For MFC/R2 Support: 'R2' will make E1 spans CAS and with the
# 'r2_idle_bits' bit in system.conf . It will also make dahdi_genconf default
# to generating the channels of this card in unicall.conf rather than in
# chan_dahdi.conf . The meaning of this may be extended somehow to support
# R2 through openr2/chan_dahdi later on.
#pri_connection_type R2
#pri_connection_type CAS
#
# Explicitly set the idle bits for E1 CAS (Sample value is the default):
#r2_idle_bits 1101
#
# Set T1 framing type to d4 instead of esf:
#tdm_framing d4
#
# Use E&M on CAS (default is FXS/FXO). If set, E1 spans will be used as
# E&M-E1 and T1 will use the requested type:
#em_signalling em
#em_signalling em_w
#em_signalling featd
#em_signalling featdtmf
#em_signalling featdtmf_ta
#em_signalling featb
#em_signalling fgccama
#em_signalling fgccamamf
#
# pri_termtype contains a list of settings:
# Currently the only setting is for TE or NT (the default is TE). This
# sets two different but normally related configuration items:
#
# A TE span will have *_cpe signalling in Asterisk and will also get
# timing from the remote party.
#
# A NT span will have *_new signalling in Asterisk and will provide
# timing to the remote party.
#
# pri_termtype is a list if span specs and configuration (TE/NT) for
# them. The first spec that matches is used. The matching is of perl
# regular expressions, but with '*' and '?' have their meaning from
# basic regular expressions.
#pri_termtype
# SPAN/2 NT
# SPAN/4 NT
#
#pri_termtype
# SPAN/* NT
#
# Astribanks can be matched by span and also by their:
# LABEL + XPD number:
# this is burned into the Astribank and won't change
# if it's connected via different USB port/hub
# CONNECTOR + XPD number:
# The USB path to which the Astribank is connected.
# Replacing an Astribank and connecting to the same USB port/hub
# would not change this property. However, any change in USB
# wiring (e.g: adding another hub) may alter this.
# NUM (XBUS number) + XPD number:
# The XBUS number. This is not stable and may even change
# between boots.
#
#pri_termtype
# LABEL/usb:INT01216/XPD-0[123] NT
# LABEL/usb:INT00375/XPD-0[123] NT
# CONNECTOR/@usb-0000:00:1d.7-1/XPD-0[123] NT
# CONNECTOR/@usb-0000:00:1d.7-2/XPD-0[123] NT
# NUM/XBUS-01/XPD-0[123] NT
# NUM/XBUS-03/XPD-0[123] NT
Code:
cat /etc/asterisk/chan_dahdi.conf
[channels]
language=fr
switchtype=euroisdn
;#signalling=bri_cpe
signalling = bri_cpe_ptmp
pridialplan=unknown
prilocaldialplan=unknown
;pridialplan=local
;prilocaldialplan = dynamic
nationalprefix=0
internationalprefix=00
priindication=outofband
faxdetect=both
overlapdial=yes
immediate=no
resetinterval=never
usecallingpres=yes
echocancel=512
;echotraining=400
language=fr
loadzone=fr
defaultzone=fr
progzone=fr
dtmfmode=inband
toneduration=300
relaxdtmf=yes
busydetect=yes
busycount=3
txgain=10
rxgain=8
;# Flash Operator Panel will parse this file for dahdi trunk buttons
;# AMPLABEL will be used for the display labels on the buttons
;# %c Dahdi Channel number
;# %n Line number
;# %N Line number, but restart counter
;# Example:
;# ;A_MPLABEL:Channel %c - Button %n
;# For Dahdi/* buttons use the following
;# (where x=number of buttons to dislpay)
;# ;A_MPWILDCARDLABEL(x):MyLabel
; include dahdi extensions defined in FreePBX
;#include chan_dahdi_additional.conf
; genere par genconf
#include dahdi-channels.conf
Au passage le fxotune -i fonctionne bien sur les 2 fxo contrairement à ce que j'avais l'autre jour sur le port freebox.
Code:
dahdi show channel 1
Channel: 1
File Descriptor: 22
Span: 1
Extension:
Dialing: no
Context: from-pstn
Caller ID:
Calling TON: 0
Caller ID name:
Mailbox: none
Destroy: 0
InAlarm: 0
Signalling Type: FXS Kewlstart
Radio: 0
Owner: <None>
Real: <None>
Callwait: <None>
Threeway: <None>
Confno: -1
Propagated Conference: -1
Real in conference: 0
DSP: no
Busy Detection: yes
Busy Count: 3
Busy Pattern: 0,0
TDD: no
Relax DTMF: yes
Dialing/CallwaitCAS: 0/0
Default law: ulaw
Fax Handled: no
Pulse phone: no
DND: no
Echo Cancellation:
512 taps
(unless TDM bridged) currently OFF
Wait for dialtone: 0ms
Actual Confinfo: Num/0, Mode/0x0000
Actual Confmute: No
Hookstate (FXS only): Offhook
Soucis détection du raccroché [Résolu]
Répondre avec citation
Envoyé par F6HQZ
